PS600 : Analog Oscilloscope (máy hiện sóng, dao động ký) của Pintek
Vui lòng tham khảo bảng giá Pintek
PS-600
CRT: |
|
Type : | Rectangular with integral graticule. |
Display Area : | 8 x 10 div ( 1 div = 1 cm ) |
Accelerating Voltage : | 12 kV. |
Phosphor : | P31. |
VERTICAL AMPLIFIERS ( CH 1 and CH 2 ) | |
Sensitivity : | 5 mV / div to 5 V / div ( X1 mode ). 1 mV / div to 5 V / div ( X5 mode ). 1-2-5 sequence, 10 step attenuator. Vernier control provides fully adjustable attenuation between steps. |
Accuracy : | ± 3 % ( X1 mode ). ± 5 % ( X5 mode ). |
Input Resistance: | 1 MΩ ± 2 %. |
Input Capacitance: | 25 pF ± 10 pF. |
Frequency Response: | 5 mV to 5 V / div ( CAL ):DC to 60 MHz (-3 dB).1 mV / div (CAL): DC to 20 MHz (-3 dB) |
Rise Time: | Approximately 5.8 ns. |
Operaing Modes: | |
CH1: | CH 1, single trace. |
CH2: | CH 2, single trace. |
ALT: | dual trace, alternating. |
CHOP: | dual trace, chopped. |
ADD: | algebraic sum of CH 1 + CH 2. |
Polarity Reversal ( Invert ): | CH 2 only. |
Maximum Input Voltage: | 400 V dc + ac peak. |
HORIZONTAL AMPLIFIER ( Input through channel 1 input ) |
X-Y mode: | switch selectable using X-Y switch. |
CH 1: | X axis. |
CH 2: | Y axis. |
Sensitivity: | 1mv/div to 5v/div |
Accuracy: | |
Y-Axis: | ± 3%. |
X-Axis: | ± 6%. |
Input Impedance: | 1MΩ ± 2% 25PF |
Frequency Response: | DC to 1 MHz typical ( -3 dB ). |
X-Y Phase Difference: | Approximately 3° at 50 kHz. |
Maximum Input Voltage: | 400V dc+ac pack |
SWEEP SYSTEM | |
Sweep Speed: | 0.1 μs/div to 2S/div in 1-2-5 sequence, 23 steps. Vernier control porvides fully adjustable sweep time between steps. |
Accuracy: | ± 3 %. |
Sweep Magnification: | 10X, ± 10% |
Holdoff: | Continuously adjustable from NORM to 5 times normal. |
TRIGGERING | |
Trigger Modes: | AUTO ( free run ) or NORM. |
Trigger Source: | CH 1, CH 2, ALT, EXT, LINE. |
Maximum External Trigger Voltage: | 300 V dc + ac peak |
Trigger Coupling: | |
AC : | 30 Hz to 60 MHz |
TV-H : | Used for triggering from horizontal sync pulses. |
TV-V : | Used for triggering from vertical sync pulses. |
Trigger Sensitivity: | |
Internal: | 0.5 division ( 1 division with TV Coupling ). |
External: | 500 mV. |
OTHER SPECIFICATIONS | |
Calibrating Voltage: | 1 kHz ( nominal ) Positive Square Wave, 2.0 V p-p ( ± 3% ) |
Trace Rotage: | Electrical, front panel adjustable. |
Power Requirements: | 115/230 VAC ± 10%, 50 / 60 Hz, approximately 40 W. |
Dimensions: | 324 x 132 x 398 mm ( 12.8 x 5.2 x 15.6" ) |
Weight: | Approximately 7.8 kg ( 17.2 1bs ) |
Rated Range of Use: | 10° C-35° C, 10-80% R.H. |
- Chi tiết
- Viết bởi TrongHuan Nguyen
- Chuyên mục: Pintek
- Lượt xem: 8892